In order to shorten a chain bracelet without cutting it, you must put the bracelet on and calculate how many connections you’ll need to remove in order for it to fit correctly. Now, gently bend each jump ring holding the closure then measure an even number of links from either side of the bracelet and reconnect the jump rings to the new end links on the bracelet. Try on the piece to check and verify whether you have fixed it right or not and are all set. Find out the steps below to know more deeply.
If you find a chain bracelet that is just a modicum too long at a store or rummage sale, adjust it yourself to make it fit properly. By using simple tools and a willingness to adjust it without cutting it, you can turn an otherwise useless piece of jewelry into a significant piece of your jewelry collection.
Tennis bracelets can be shortened in the same way due to the way they’re made, the removed piece is challenging to reattach because the connecting portion that gives the tennis bracelet its flexibility has been severed. Let’s look into it.
Rope chains, snake chains, and thick, stone-studded Cuban/curb chains are more difficult to shorten than other chains. While the premise of removing a portion and reattaching the clasp to the rest of the item stays the same, the process for these things is unchangeable. Let’s see the steps.
- Step 1
Put the bracelet on and calculate how many connections you’ll need to remove in order for it to fit correctly.
- Step 2
Now, gently bend each jump ring holding the closure and retaining ring apart from the piece’s opposing ends. A jump ring is a tiny incision on one edge of a circular piece of metal. This extends the ring about a millimeter, allowing it to be slid over the clasp. The retaining ring is the metal element to which the lobster clasp is attached.
- Step 3
Measure an even number of links from either side of the bracelet while reassembling it to ensure that any features remain centered between the ring and clasp. With the wire snips, cut these links off. To avoid mistakenly cutting into another link, use the tip of the snips.
- Step 4
Using the needle-nose pliers, reconnect the jump rings to the new end links on the bracelet. As you close the loops you made previously, hold one side of the ring in one hand and the pliers in the other.
- Step 5
Now finally try on the piece to check and verify whether you have fixed it right or not.
Have a long useless necklace? know How To Make A Necklace Shorter
If you wish to shorten a closed-ring chain, you’ll need to remove the clasp and then use cutters or jeweler’s shears to cut the links. All that’s left is to replace the clasp, and you’re done.
Before you begin a project, consult our chart to determine the appropriate chain length for a long necklace, a choker, a princess necklace, or a matinee necklace.
There are additional options if you don’t want to cut your chain or if the links are too complicated, like, the Serpentine link, ball link, etc. to cut without modifying the link:
- Make a multi-range bracelet by wrapping multiple rounds around your wrist, or a choker by wrapping several turns over your neck.
- Slip a pendant onto your chain and tie a knot just above it if your chain isn’t too long.
- Place your clasp on a different area of the chain, on a separate link. When you close your necklace, the length of the chain will hang down as if it were an extension chain.
Does Brass Turn Your Skin Green?Know everything about it.
- Assemble your supplies first. You’ll need the correct supplies for this, but they’re not difficult to get by. Two pairs of long-nose pliers, preferably the bent sort, are required to shorten a chain. These are commonly used by jewelry makers, but they’re also found in a handyman’s toolbox, so ask around if you don’t have any.
- Estimate the connections you want to get rid of. It’s best to underestimate this because reattaching links is slightly more difficult than removing them.
- Find the junction on a link, then open the links with your quasi-hand and a set of long nose tweezers on one side of the seam.
- Now just reconnect the chain.
Frequently Asked Questions –
1.How do you shorten a chain bracelet without cutting it?
Removing seams or junctions for the portion you think needs to be alleviated and connecting the ends again should work in order for it to be shortened.
2.How do you fix a bracelet that is too big?
Wear it over a sleeve or a glove if the bracelet is too big. A layer of leather or the rough fabric of a sleeve will give the bracelet something to cling to, and the closer fit will be much more pleasing as a result.
3.How do you shorten a chain at home?
You can use your regular toolbox and pilers to first estimate the portion you want to get rid of and then reattach the ends after removing the previously mentioned portion. You are done!